Technical Parameters
Basic Parameters
| Parameter | Condition | Value |
|---|---|---|
| Temperature Range | Operating Storage | -40 °C to +75 °C -40 °C to +85 °C |
| Humidity | Operating Storage | 5 to 95 % relative humidity, non-condensing 5 to 95 % relative humidity, non-condensing |
| Altitude | Operating | 2000 m / 70 kPa |
| Degree of Protection | IP30 | |
| Supply Voltage | 9 to 48 V DC | |
| Battery for RTC | CR1225 | |
| Dimensions (without clip) | 113.2 × 80.3 × 42 mm (metal box) 117 × 83.8 × 51.4 mm (plastic box) | |
| DIN Rail Clip | DIN 35 mm, EN 60715 | |
Device Weight
| Model | Metal box | Plastic box |
|---|---|---|
| ICR-2701 | 230 g | 170 g |
| ICR-2734 | 260 g | 200 g |
| ICR-2834 | 300 g | 240 g |
Consumption
The following consumption values are measured at the supply voltage input:
| Model | Idle [W]¹ | Average [W] | Maximum [W] | LPM Mode [mW] |
|---|---|---|---|---|
| ICR-2701 | 1.4 / 1.8 | 1.4 / 1.9 | 5.3 / 5.8 | 3 |
| ICR-2734 | 1.6 / 2.3 | 3.0 / 4.0 | 6.9 / 7.7 | 3 |
| ICR-2834 | 1.9 / 2.3 | 3.5 / 4.0 | 7.4 / 7.7 | 6 |
¹ Values shown as non-Wi-Fi / Wi-Fi.
Standards and Regulations
The routers comply with the following standards and regulations:
ICR-2701
| Parameter | Description |
|---|---|
| Radio | ETSI EN 301 893, ETSI EN 300 328 |
| EMC | ETSI EN 301 489-1, ETSI EN 301 489-17, EN 55032, EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61000-4-5, EN 61000-4-6, EN 61000-6-2, EN 61000-6-3 |
| Safety | EN IEC 62368-1, EN IEC 62311, IEEE 802.3 |
| Transportation | E-Mark (E8), homologation number: 10R-06 13493¹ |
| Cybersecurity | EN 18031-1 |
| National | CE, UKCA compliant |
| Environmental | REACH, RoHS3 and WEEE compliant |
¹ Not applicable to Wi-Fi models.
ICR-2734
| Parameter | Description |
|---|---|
| Radio | ETSI EN 301 511, ETSI EN 301 908-1, ETSI EN 301 908-2, ETSI EN 301 908-13, ETSI EN 301 893, ETSI EN 300 328 |
| EMC | ETSI EN 301 489-1, ETSI EN 301 489-17, ETSI EN 301 489-52, EN 55032, EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61000-4-5, EN 61000-4-6, EN 61000-6-2, EN 61000-6-3 |
| Safety | EN IEC 62368-1, EN IEC 62311, IEEE 802.3 |
| Transportation | E-Mark (E8), homologation number: 10R-06 13493¹ |
| Cybersecurity | EN 18031-1 |
| National | CE, UKCA, UK compliant |
| Environmental | REACH, RoHS3 and WEEE compliant |
¹ Not applicable to Wi-Fi models.
ICR-2834
| Parameter | Description |
|---|---|
| Radio | ETSI EN 301 511, ETSI EN 301 908-1, ETSI EN 301 908-2, ETSI EN 301 908-13, ETSI EN 303 413, ETSI EN 301 893, ETSI EN 300 328 |
| EMC | ETSI EN 301 489-1, ETSI EN 301 489-17, ETSI EN 301 489-19, ETSI EN 301 489-52, EN 55032, EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61000-4-5, EN 61000-4-6, EN 61000-6-2, EN 61000-6-3 |
| Safety | EN IEC 62368-1, EN IEC 62311, IEEE 802.3 |
| Transportation | E-Mark (E8), homologation number: 10R-06 13493¹ |
| Cybersecurity | EN 18031-1 |
| National | CE, UKCA, UK compliant |
| Environmental | REACH, RoHS3 and WEEE compliant |
¹ Not applicable to Wi-Fi models.
Type Tests and Environmental Specifications
Routers undergo the following tests to ensure durability and reliability:
ICR-2701 and ICR-2734
| Phenomena | Test | Description | Test levels |
|---|---|---|---|
| ESD | EN 61000-4-2 | Enclosure | CD ± 6 kV, L3 AD ± 8 kV, L3 |
| RF field AM modulated | EN 61000-4-3 | Enclosure | 20 V/m, 80 MHz – 1 GHz, LX 10 V/m, 1 GHz – 6 GHz, L3 |
| Fast transient | EN 61000-4-4 | DC ETH — FTP AC/DC | ± 1 kV, 5/50 Tr/Th ns, 100 kHz, L2 ± 1 kV, 5/50 Tr/Th ns, 100 kHz, L3 ± 2 kV, 5/50 Tr/Th ns, 100 kHz, L3 |
| Surge | EN 61000-4-5 | DC ETH AC/DC | ± 1 kV, 1.2/50(8/20) Tr/Th µs, L2 ± 1 kV, 1.2/50(8/20) Tr/Th µs, L2 ± 2 kV, 1.2/50(8/20) Tr/Th µs, L3 |
| RF conducted | EN 61000-4-6 | DC ETH AC/DC | 10 V, 0.15–80 MHz, 80 % AM (1 kHz), L3 10 V, 0.15–80 MHz, 80 % AM (1 kHz), L3 10 V, 0.15–80 MHz, 80 % AM (1 kHz), L3 |
| Dips & interruptions | EN 61000-4-11 | AC/DC | Dip 0 % (0.5 cycle), 0 % (1 cycle), 70 % (25 cycles); interruption 0 % (250 cycles) |
| Radiated & conducted emission | EN 55032 | Enclosure DC ETH AC/DC | Class B, 30 MHz – 1 GHz, 1 GHz – 6 GHz Class B, 150 kHz – 30 MHz Class B, 150 kHz – 30 MHz Class B, 150 kHz – 30 MHz |
ICR-2834
| Phenomena | Test | Description | Test levels |
|---|---|---|---|
| ESD | EN 61000-4-2 | Enclosure | CD ± 6 kV, L3 AD ± 8 kV, L3 |
| RF field AM modulated | EN 61000-4-3 | Enclosure | 20 V/m, 80 MHz – 1 GHz, LX 10 V/m, 1 GHz – 6 GHz, L3 |
| Fast transient | EN 61000-4-4 | DC ETH — FTP RS232 RS485 Digital input Digital output AC/DC | ± 1 kV, 5/50 Tr/Th ns, 100 kHz, L2 ± 1 kV, 5/50 Tr/Th ns, 100 kHz, L3 ± 1 kV, 5/50 Tr/Th ns, 100 kHz, L3 ± 1 kV, 5/50 Tr/Th ns, 100 kHz, L3 ± 1 kV, 5/50 Tr/Th ns, 100 kHz, L3 ± 1 kV, 5/50 Tr/Th ns, 100 kHz, L3 ± 2 kV, 5/50 Tr/Th ns, 100 kHz, L3 |
| Surge | EN 61000-4-5 | DC ETH AC/DC | ± 1 kV, 1.2/50(8/20) Tr/Th µs, L2 ± 1 kV, 1.2/50(8/20) Tr/Th µs, L2 ± 2 kV, 1.2/50(8/20) Tr/Th µs, L3 |
| RF conducted | EN 61000-4-6 | DC ETH RS232 RS485 I/O AC/DC | 10 V, 0.15–80 MHz, 80 % AM (1 kHz), L3 10 V, 0.15–80 MHz, 80 % AM (1 kHz), L3 10 V, 0.15–80 MHz, 80 % AM (1 kHz), L3 10 V, 0.15–80 MHz, 80 % AM (1 kHz), L3 10 V, 0.15–80 MHz, 80 % AM (1 kHz), L3 10 V, 0.15–80 MHz, 80 % AM (1 kHz), L3 |
| Dips & interruptions | EN 61000-4-11 | AC/DC | Dip 0 % (0.5 cycle), 0 % (1 cycle), 70 % (25 cycles); interruption 0 % (250 cycles) |
| Radiated & conducted emission | EN 55032 | Enclosure DC ETH RS232 RS485 AC/DC | Class B, 30 MHz – 1 GHz, 1 GHz – 6 GHz Class B, 150 kHz – 30 MHz Class B, 150 kHz – 30 MHz Class B, 150 kHz – 30 MHz Class B, 150 kHz – 30 MHz Class B, 150 kHz – 30 MHz |
Cellular Module Parameters
Tips
This section applies to ICR-2734 and ICR-2834. ICR-2701 is a LAN router and does not include a cellular module.
| Parameter | Description |
|---|---|
| Antenna | Connector type: SMA Input impedance: 50 Ω |
| LTE parameters | LTE: Cat.4, 3GPP Rel. 10 FDD frequencies: B28 (700 MHz), B20 (800 MHz), B5 (850 MHz), B8 (900 MHz), B3 (1800 MHz), B1 (2100 MHz), B7 (2600 MHz) Bit rates: 150 Mbps (DL) / 50 Mbps (UL) Max. output power: 23 ± 2 dBm |
| HSPA+/UMTS parameters | HSPA: 3GPP Release 7 UMTS: 3GPP Release 4 Supported frequencies: B8 (900 MHz), B3 (1800 MHz), B1 (2100 MHz) Bit rates: max. 21 Mbps (DL) / 5.7 Mbps (UL) Max. output power: 24+1/−3 dBm |
| EDGE/GPRS parameters | Supported frequencies: B5 (850 MHz), B8 (900 MHz), B3 (1800 MHz), B2 (1900 MHz) Bit rates: max. 237 kbps (DL) / 237 kbps (UL) Max. output power: 33 ± 2 dBm |
GNSS Parameters
Tips
This section applies to ICR-2834 only.
Warning
GNSS is supported by models with the GNSS module only. Refer to the Order Codes section for details.
| Parameter | Description |
|---|---|
| Protocol | NMEA |
| GNSS Systems | GPS, GLONASS, BeiDou, Galileo |
| Antenna | Connector type: SMA Input impedance: 50 Ω Power mode: 3 V / 20 mA supply for active antenna Automatic power saving modes |
| Frequency | GPS: 1575.42 MHz (1574.4 – 1576.4 MHz) GLONASS: 1597.5 – 1605.9 MHz |
| Tracking Sensitivity (open sky) | GPS (active antenna): −159 dBm GLONASS (active antenna): −158 dBm GPS (passive antenna): −156 dBm GLONASS (passive antenna): −156 dBm |
| Acquisition Sensitivity (open sky) | GPS (active antenna): −147 dBm GLONASS (active antenna): −146 dBm GPS (passive antenna): −145 dBm GLONASS (passive antenna): −144 dBm |
| TTFF (at −130 dBm) | Warm start: 28 s Cold start: 32 s |
Wi-Fi Parameters
Caution
The 5 GHz Wi-Fi interface operates in frequency bands (specifically 5150–5350 MHz) that are restricted to indoor use only in certain EU member states. Refer to the regulatory documentation for your router model for details.
| Parameter | Description |
|---|---|
| Supported Standards | IEEE 802.11a/b/g/n/ac, 2.4 GHz & 5 GHz |
| Antenna Connector | 1× RP-SMA, input impedance: 50 Ω |
| Data Rate | 802.11b: 1, 2, 5.5, 11 Mbps 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54 Mbps 802.11n: max. 72 Mbps @ 20 MHz / max. 150 Mbps @ 40 MHz channel |
| Frequency Ranges | 2.4 GHz ISM: 2.412 – 2.472 GHz 5.15 – 5.25 GHz (EU and US/Canada) 5.25 – 5.35 GHz (EU and US/Canada) 5.47 – 5.725 GHz (EU only) 5.725 – 5.825 GHz (US/Canada only) |
| Modulation | DSSS, OFDM, DBPSK, DQPSK, CCK, 16-QAM, 64-QAM |
| 2.4 GHz Supported Channels | 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13 |
| 5 GHz Supported Channels | 36, 38, 40, 42, 44, 46, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165 |
| Type of Device | Access point (AP, up to 8 clients), Station (STA), Multi-role (STA & AP) |
| Security — Standards | WPA, WPA2, WPA3, 802.1X |
| Security — Encryption | WEP, TKIP, AES |
| TX Power¹ | Max. 18 dBm @ 2.4 GHz Max. 15 dBm @ 5 GHz |
¹ The maximum transmit power is determined by the Country setting in the router's web interface.
I/O Parameters
Tips
- This section applies to ICR-2834 only.
- The digital input status is available in the router's web interface (General Status page) and via the status ports and io get commands — refer to the Command Line Interface application note.
Characteristics of digital inputs:
| Logical¹ | Voltage | Current | Status² |
|---|---|---|---|
| 1 | 3 V | 0.5 mA | Off |
| 0 | 5 V | 0.8 mA | On |
| 0 | 12 V | 1.6 mA | On |
| 0 | 48 V | 3.4 mA | On |
¹ The digital status returned by the io get shell command.
² The digital status returned by the status ports shell command and displayed on the General Status page.
The maximum digital output load is 500 mA at 48 V.
Serial Interfaces
Tips
The RS232 and RS485 interfaces can be configured in Expansion Port 1 and Expansion Port 2.
| Parameter | Description |
|---|---|
| Baudrate | 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400 bps |
| Data Bits | 5, 6, 7, 8 |
| Parity | None, even, odd |
| Stop Bits | 1, 2 |
| Flow Control | None, hardware |
System Configuration
| Parameter | Description |
|---|---|
| CPU Architecture | 32-bit ARM926EJ-S |
| CPU Frequency | 600 MHz |
| CPU Power | 4.72 DMIPS/MHz |
| Flash Memory | 4 MB NOR 4096 MB eMMC: • 838 MB for Router Apps • 512 MB for customer data • Remaining space reserved for system |
| RAM | 128 MB |
| Watchdog | HW watchdog |
| RTC | Battery backup RTC |
| TPM¹ | Trusted Platform Module (TPM) 2.0 |
¹ Not assembled by default; available for dedicated customer orders only.